An SLA uptime percentage is a promise about how much of the time a service will be working. The SLA uptime calculator turns that percentage into the downtime it actually allows, so you can see whether 99.9% means minutes or hours of outage per month.

Every SLA has an uptime target, usually written as a percentage like 99.9% or 99.99%. That number sounds precise, but it is hard to judge until you convert it into minutes of allowed downtime for the period your SLA measures.

How uptime is calculated

Uptime percentage is the share of the measurement period during which the service was available. The formula is simple: uptime equals available time divided by total time, multiplied by 100.

Allowed downtime is the other side of the same calculation. Subtract the uptime percentage from 100%, then multiply by the length of the period. A 99.9% target over a 30.44-day month (a 365-day year divided by 12) allows 43 minutes and 48 seconds of downtime.

This calculator uses a 365-day year, with a month equal to the year divided by 12 and a quarter equal to the year divided by 4. That matches how most SLAs are written, and it keeps monthly and yearly figures consistent with each other.

Worked example

Take a service with a 99.9% monthly SLA. The month is 30.44 days, which is 43,829 minutes. The allowed downtime is 0.1% of that, or 43.83 minutes — 43 minutes and 48 seconds.

The same 99.9% target measured over a full year allows 8 hours, 45 minutes, and 36 seconds of downtime. That is the same percentage, but the budget is very different, which is why the measurement window matters so much in a contract.

Now compare 99.99% over the same month. The allowed downtime drops to 4 minutes and 23 seconds. One extra nine cuts the budget by a factor of ten, and that is why the price of the next nine is usually steep.

How to use the result

Start by entering the uptime percentage from your SLA and the period it is measured over. The calculator shows the allowed downtime for that period and for the other common periods, so you can compare a monthly vendor promise against an annual internal target.

Use the monthly figure when you are checking a vendor’s SLA compliance or deciding whether a service credit is owed. If the vendor was down for 50 minutes in a month on a 99.9% SLA, the target was missed.

Use the yearly figure when you are setting an internal target or budgeting for risk. A team that can tolerate one long outage a year but not many small ones may prefer an annual target, while a team running a customer-facing service usually needs the monthly check.

Note: The calculator truncates the uptime percentage to three decimal places and never rounds it up. A service at 99.949% is reported as 99.949%, not 99.95%, so a borderline result is never shown as a pass.

What a good target looks like

There is no single right number. Internal tools that staff can work around often run fine at 99% or 99.5%, while a checkout page or a payment service usually needs 99.9% or better. The right target is the one where the cost of the next nine is less than the cost of the downtime it prevents.

If you are writing the SLA itself, pair the percentage with a clear measurement window, a definition of downtime, and a service credit. A percentage without those three details is hard to enforce, however impressive it looks. The SLA template gives you a starting point for all three.

When downtime does happen, its cost is rarely just the minutes. Use the downtime cost calculator to turn those minutes into a dollar figure you can take to a budget meeting.

Frequently asked questions

What does 99.9% uptime actually allow?

99.9% uptime allows 43 minutes 48 seconds of downtime per month and 8 hours 45 minutes 36 seconds per year, using a 365-day year and a month of year divided by 12.

Is downtime measured per month or per year?

It depends on your SLA. Most vendor SLAs measure uptime monthly, while internal targets are often annual. Always check the measurement window before you compare two numbers.

Does scheduled maintenance count as downtime?

Most SLAs exclude scheduled maintenance from the uptime calculation, but only when the vendor announced it in advance and inside an agreed window. Unplanned outages always count.

What is the difference between uptime and availability?

Uptime is the share of time a service was running. Availability is the same idea measured from the user's side, including whether the service was reachable and usable. In most SLAs the two terms are used interchangeably.

How many nines do I need?

It depends on the cost of an outage. 99% allows over 7 hours of downtime a month, 99.9% allows about 43 minutes, and 99.99% allows about 4 minutes. Each extra nine usually costs much more than the last.